SKU:
Safe payments with trusted SSL protection
The 3,500 lb. Deluxe Flat-Plate Boat Hoist combines a 3/4 HP Painted Wired Boat Lift Motor and a 6,500 lb. Deluxe Gear Plate Assembly to create a boat hoist.
The 6,500 lb. Deluxe Gear Plate Assembly includes the 10-inch aluminum die-cast hoist pulley, 96-tooth cast iron worm gear assembly, extended block bronze worm assembly, and 34-inch drive belt.
There are no steel-on-steel moving parts. It has been assembled and tested by the manufacturer. Lifetime warranty included. You can choose between galvanized steel, 1/2 in. aluminum, or powder-coated steel for the backplate.
The 3/4 HP Painted Wired Boat Lift Motor is a single-phase motor with start capacitors. Standard duty motors. Factory-wired for 110 volts. An electrician can rewire it to 220 volts. Fits all BH-USA flat-plate hoists and gear plates. Fits other brands using the standard 4 ft x 2 ft flat-plate mounting holes.
NEMA 56 frame motor. UL/CSA listed and approved. TENV (totally enclosed, non-ventilating) housing. TENV housing prevents dirt, insects, and water from entering the motor.
Maximum runtime: 15 minutes. Finished in black. Includes colored T-wires. Includes easy-to-follow instructions. Equipment guide and wiring instructions included.
A motor wire harness is installed directly on the electrical motor. Depending on your preference, you can select a maintained (lock-on) or momentary (spring-loaded) drum switch type. The in-line GFCI has a built-in test and reset button.
The extended block worm assembly has a 2-inch bearing block, a worm on a driveshaft, and an aluminum housing with 1/4-inch grease fittings. Attaches directly to the gear plate. The assembly has standard flat-plate mounting holes.
The 96 tooth worm gear assembly comes assembled with the gear, sleeve, backplate bearing, axle sleeve bolt, and snap rings. 1/4 inch easy-reach grease fittings are included. The gear fits standard gear plates used in flat-plate hoists.
The 10 in. Aluminum Die-Cast Hoist Pulley is made from an aluminum die-casting process. They are much stronger in marine environments and will not swell or bend. The belt-gripping technology on the inside of the pulley prevents belt slippage. Compatible with any known flat-plate hoist. Resistant to warping. Designed to fit drive belts better. The bore is 3/4 inches. Accepts belts up to 1/2 inch.
The AX-34 is a 34-inch drive belt that is compatible with all flat-plate boat hoists from BH-USA. This belt is the perfect length to fit around a 10-inch hoist pulley and to be able to attach it to a 2-inch motor pulley. As the motor’s driveshaft turns, the pulleys turn the belt in order to complete the movement of the hoist.
Rated Capacity: 3500 lbs
Test: Straight-line
Dimensions: 12 in. L x 24 in. H
Plate Thickness: 1/4 in. – 1/2 in.
Bull Gear Ratio: 96:1
GPA Warranty: Lifetime
Extended Block Worm Assembly
Worm Material: Bronze
Thread: Single
Thread Direction: Right hand
Worm Diameter: 1 3/4 in.
Worm Length: 2 in.
Worm Bore: .754 in.
Grease Fittings: 3
Fitting Size: 1/4 in.
Dimensions: 1 1/4 in. x 1/2 in.
Collars Included: 2
Collar Set Screw: 5/16 in.
96 Tooth Worm Gear Assembly
Material: Cast Iron
Gear Bore: 2.875 in.
Diameter: 12 3/4 in.
Hub Depth: 2 in.
10 in. Pulley & AX-34 Belt
Material: Aluminum
Type: Die-cast
Holds: 1 belt
Size: 10 in.
Bore: 3/4 in.
Belt Size: 34 in.
Type: Cogged
Hoist Pulley Fits 10 in.
Motor Pulley Fits: 2 in.
Motor
Horsepower: 3/4
Frame: 56
RPM: 1725
SF: 1.0
Voltage: 115v / 230v
Phase: 1
Amps: 10.8 (110v) /5.4 (220v)
SFA 6.2
Herz: 60
AMB: 40°c
HSG: TENV
Code: L
Insulation: B
Max. Run Time: 15 min.
Finish: Painted
Shaft Dua: 5/8 in.
Electric Motor Wire Harness
110v Plug: 3-US 110v Standard
220v Plug: US 240v NEMA 6-15
Switch Size: 3.5″ x 4.5″ x 4.5″
Max. Amps: 20
Max. HP: 1 1/2
Compliance: UL, NEMA, CE, SA
VAC: 120-240
Box Color: Gray
Material: Plastic
Handle: Red
Type: Maintained / Momentary
Cable: 14/5 SJTW
GFCI-to-Plug: 4 1/2 in.
Box-to-GFCI: 60 in.
Class: A-Rainproof
Amp: 15
Hz: 60
Voltage: 125v / 240v
Reset: Automatic
Cord Dia.: .28 – .65
Motor Pulley
Size: 2 in. x 2 in. x 2 in.
Material: Aluminum
Bore Size: 5/8 in. (.630 in.)
Type: Center bore
Set Screw: 3/8 in.
Thread: 16 (coarse)
Build: Machined
Fits: Single
Mount: 56-Frame
